Owner’s GuideHeavy Duty Inverter/Charger1000 Watt Weatherproof Model RM1012For Volvo Trucks
Introduction1–4Operating featuresInverter/charger The inverter/charger operates as an inverter and as a charger depending upon the operational conditi
Operating features1–5Charger featuresXantrex HD offers the following charger features:• 50 amp charging, when shorepower is connected, to ensure your
2 Operation Chapter 2, “Operation” explains how to calculate the size of the loads you can run from the Xantrex HD Inverter/Charger. It also provides
Operation2–2Planning for AC loadsAC load AC load refers to an AC product you want to operate from the inverter/charger. Loads include most products th
Planning for AC loads2–3DC loadsDC loads are those that run off the 12 V electrical system on the truck. A few examples of DC loads are:• marker light
Operation2–4intersection of the time and temperature will indicate approximately the output power of the unit. For example, between – 40 °F (– 40 °C)
Planning for AC loads2–5Factors affecting loadConsider these factors when you are calculating loads:• Loads that exceed 1000 watts may be run for a sh
Operation2–6* AverageThe inverter/charger shuts down after 24 hours if it does not detect a load (or loads less than 20 W).† Based on four minute oper
Planning for AC loads2–7Driving the truck while operating AC and DC loadsRecharging Driving your truck does not guarantee that the battery is being fu
About XantrexXantrex Technology develops, manufactures, and markets advanced power electronic products. The company’s products convert raw electrical
Operation2–8The efficiency of the inverter/charger is approximately 90%, which means it is drawing about 1100 W (DC) from the battery or 92 amps. This
Using the toggle switch2–9Using the toggle switchLocation The inverter/charger is controlled from the remote toggle switch on the control panel in the
Operation2–10Switch LEDs The LEDs provide information about the operating state of the inverter/charger. Under normal operating conditions the lights
Operating the Inverter/Charger2–11Operating the Inverter/ChargerThis section provides guidelines for operating the Xantrex HD.Turning the inverter on
Operation2–12Battery chargingWhen you are connected to shorepower, the AC LED is illuminated and the unit is both passing power through to the applian
3–13 MaintenanceChapter 3, “Maintenance” provides procedures for checking the terminal connections on the inverter/charger, disconnecting Xantrex HD f
Maintenance3–2Checking terminalsTo check that the battery cables are firmly connected, you will need to remove the terminal caps.To remove the termina
Disconnecting and connecting Xantrex HD from the batteries3–3Disconnecting and connecting Xantrex HD from the batteriesBefore doing any work with your
Maintenance3–43. Connect the positive battery cable from the inverter/charger to the positive terminal on the battery; then the negative to the negati
Replacing the fuse3–5.3. Replace the fuse cover by placing it over the fuse and pressing down until it snaps into place.If the fuse blows a second tim
iiiImportant Safety InformationGeneral precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vPrecaution
Maintenance3–6Removing and reconnecting AC cablesTo remove the AC cables:➣ Grasp the knurled surface of the connector housing as shown in Figure 3-3 a
4 TroubleshootingChapter 4, “Troubleshooting” provides information to help you identify common problems which may occur. Read this chapter before call
Troubleshooting4–2TroubleshootingCommon problemsThe unit shuts down during operation for four main reasons:• low battery—when the battery reaches appr
Troubleshooting4–3Blinking lights on the remote switchThis table describes the different sequences of blinking lights you may encounter when the inver
Troubleshooting4–4Table 4-2 explains the blinking pattern of the AC input LED when the inverter is connected to shorepower.Table 4-3 explains the inve
Calling your authorized Volvo dealer4–5Calling your authorized Volvo dealerIf none of the troubleshooting suggestions work, you will need to call your
4–6
A SpecificationsAppendix A “Specifications” contains the Xantrex HD product specifications, which include the inverter, charger, and transfer specific
SpecificationsA–2Physical specificationsPhysical specificationsEnclosure Sealed; dust and water-resistantDimensions Approximately. 8.5" (21.8 cm)
Inverter specificationsA–3Inverter specificationsAll inverter specifications are at nominal conditions; 77 °F (25 °C,) 1000 W resistive load, 12 Vdc i
Contentsiv3MaintenanceChecking terminals- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3–2Disconnecting and conn
SpecificationsA–4Charger specificationsAll charging specifications are at nominal conditions, 77 °F (25 °C), 14.0 Vdc at 50 A charging, 120 Vac, 60 Hz
Transfer and general specificationsA–5Transfer and general specificationsTemperature compensation – 0.023 Vdc/ °C from -2 °C to 85 °C.Below -2 °C, the
SpecificationsA–6Rating curves and charging profilesFigure A-1 Output surge ratingFigure A-2 Charging current versus temperature derating curve0500100
Rating curves and charging profilesA–7Figure A-3 Three-stage charging profileBulkAbsorption ChargeFloat ChargeDC VoltageDC CurrentConstant Current@ Ma
AAC cables, removing or connecting 3–6AC loadcalculating size 2–4definition 2–2factors affecting 2–2types of 2–2AC power, connect delay 2–12alternator
IndexIX–2Fflashlights see problem loadsfuse, over-current protection 1–3fuse, replacing 3–4Hhigh battery shutdown 4–2Iinductive load see AC loadsinve
IX–3IndexTtemperature see ambient temperaturetemperature and power, relationship of 2–3temperature and time derating curve (figure) 2–4terminals caps
vImportant Safety InformationGeneral precautions1. Before using the inverter/charger, read all appropriate sections of this guide and any cautionary m
Important Safety Informationvi3. Never smoke or allow a spark or flame near the engine or battery.4. Use caution to reduce the risk of dropping a meta
1 IntroductionChapter 1, “Introduction” describes the main performance and protection features of the inverter/charger.
Introduction1–2Introduction to the Xantrex HDFeatures The Xantrex HD inverter/charger is a weatherproof, modified sine wave inverter/charger designed
Introduction to the Xantrex HD1–3Location The inverter/charger is mounted on the main rail of the truck adjacent to the battery compartment as shown i
Kommentare zu diesen Handbüchern